11/25/2023 0 Comments Process lasso performance modeWe hope you enjoy these new product releases, and appreciate the continued support of our customers that makes further development possible. Previous editions of Windows would have split the 128 logical CPU cores of the AMD 3995WX into two NUMA nodes bounded by the two processor groups. 3995WX CPU Topologyįinally, it is worth noting that this release supports a new Windows CPU topology that allows a single NUMA node to span multiple processor groups, used namely by the AMD 3995WX CPU on Windows 11. Process Lasso has always shown both metrics in its status bar, and that continues. A new option allows the user to toggle which metric is relied on by the CPU graphs. It therefore takes into account processor frequency scaling, so will tend to be higher than CPU Time %, and can exceed 100%.ĬPU Utility % is used by Task Manager, and now by default in Process Lasso. The newer measurement, CPU Utility %, is the percent of total computational capacity actually used at the current CPU frequency. This is the percent of available CPU time that the processor spent executing code. There are multiple valid metrics to represent CPU use. In the case of ParkControl, support means that CPU core parking and frequency scaling can be tuned for the individual Power Modes, and the newly refactored Dynamic Boost feature can be configured to use them.įor further reading on Power Modes and the Performance Power Slider, see this page. For instance, users can specify a Power Mode to be entered whenever a particular process is running, or when the device goes idle. Support of Power Modes means that all Process Lasso power automation features can make use of them. The stock Windows Power Modes are: Better Battery Portable device users will only know these modes, while desktop users may need to switch to Balanced, and then to a Power Mode (using the Power Performance Slider in the tray or Power Settings) to see them. They were introduced in Windows 10, build 1709. Windows Power Modes are overlays of the Balanced power plan that set the system’s power to performance ratio without changing other power settings such as the sleep timeout. ParkControl v3.0 was also released with Power Mode support and UI improvements. After doing this, restart Process Lasso for them to show up.įor more information, see this Microsoft documentation: Customize the Windows performance power slider.Process Lasso v12.0 adds support for Power Modes, new processor topologies (3995WX), and changes the default CPU use metric to CPU Utility %. Alternatively, the battery icon in the tray can be used to select a Power Mode. Users can switch to Power Modes (overlays) by entering the ‘Balanced’ power plan, then opening the System Power settings and selecting one of the three Power Modes, as shown below. Using this method, the manual steps described above are not necessary. It will install BHP and show it alongside power modes. UPDATE: As of Process Lasso v12.3.2 beta and ParkControl v4.1.0 beta, an experimental option to ‘Always Show Bitsum Highest Performance’ is available. A caveat, however, is that if you switch back to a power mode and restart either product, it will no longer show the Bitsum Highest Performance power plan. Finally, run the Process Lasso or ParkControl installer again to add the Bitsum Highest Performance power plan. Then make the new power plan active by switching to it. Users can switch back to traditional power plans by opening the legacy Control Panel Power Options and clicking the link ‘ Create a power plan‘, as shown below. The Bitsum Highest Performance power plan that comes with Process Lasso and ParkControl can only be installed when the system is using traditional power plans. The stock Power Modes are: Better Battery Settings such as display time-out are static across all modes of the Balanced power plan.Ī Performance Mode Slider on the battery icon in the system tray provides access to these modes, as does the Power Settings of Windows. These modes only change processor performance settings, thus can be considered ‘light’ power plans. They call these new overlays of the Balanced plan, ‘Power Modes’. Download Bitsum Process Lasso Pro 12 Compact software statistics and troubleshoot computer systems, such as crashes by way of control CPU. On these systems, beginning with Windows 10 build 1709, Microsoft extended the Balanced power plan horizontally and eliminated the additional power plans. Many Windows based computers now have only a singular power plan: Balanced. If you want to tweak that power plan, you can use our free ParkControl app. In this case, the BHP power plan is not necessary and ‘Maximum Performance’ should be used instead. If only you see ‘overlays’ and no Bitsum Highest Performance (BHP) power plan, that means your system is using Power Modes in lieu of traditional power plans. FAQ: I only see ‘overlays’ and no Bitsum Highest Performance.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |